Summer Starts Here - Save up to 70%
Trailer Wiring Harness Installation - 2009 Saturn Vue- Video
Today on this 2009 Saturn View we'll be installing a Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part number C56026. We'll glue the fastener at the bottom of the inner cargo pocket. Using a flat blade screwdriver go ahead and twist out the plastic cap nut. Once we have all of the fasteners out of the corner panel we'll then go ahead and remove the corner pocket. The corner pocket has a push pin fastener in the bottom, so we'll get underneath it and gently pull it up until it releases. To remove the corner pocket I'm just using a plastic pry tool. more
12/22/2014 1:24:06 PM
TowReady Taillight Converter Hardwire Kit Installation - 2007 Saturn Vue- Video
Today in this 2007 Saturn Vue we're going to install part number 119178KIT. This will actually be easy install. This will use a tow package that's already existing in the vehicle. We need to open up the back hatch and get access to jack storage compartment. We'll open up the door, and we'll go ahead and remove the jack tools. Towards the bottom of the pocket you'll see some loops of wires. We'll go ahead and free those wires up to get better access to them. These wires are in a continuous loop so it's just as well just to leave them like they are, just work out the electric tape to make sure you've better access to them that you can work with. At this point we can go ahead and start taking our converter and attaching it to the tow pack. This will almost be color for color wiring. We'll take our green wire from our converter box and match the green wire on the tow package on the car. We'll do the same thing with the yellow wire and also the brown wire. To make our connections we'll be using the quick splice connectors. Put our quick splice connector on the wire, then slide a new wire next to it and the slowly press down on the metal part in the middle with a pair of pliers to make our connection. more
11/26/2013 4:48:58 PM
Trailer Wiring Harness Installation - 2009 Saturn Vue 118443- Video
Today on our 2009 Saturn Vue will be installing Tow Ready T-One Connector, part number 118443. Now to begin our installation, we'll need to open the rear left gate, remove the threshold plate, the trunk floor panels and the spare tire tray from the vehicle. Now on the driver side of the vehicle, we need to remove the fasteners that hold the black Styrofoam tray where we can then carefully pry the black tray out from the underneath the side panel. We'll next locate the plastic side pocket inside the driver's side trim panel. We also need to remove the screw here, slowly pull up on the tray until it pops out of the panel. This will expose our wiring that are T-One Connector will tap. more
11/21/2012 11:46:41 AM
Trailer Wiring Harness Installation - 2003 Saturn Vue- Video
Today on our 2003 Saturn Vue, well be installing the Tow Ready T1 Connector, part number 118418. Before we begin the installation, weve gone ahead and raised the vehicle and removed the rear wheels. Now, were going to open up the rear cargo door and remove the two fasteners securing the passengers side tail light assembly. Once we have the assembly loose, well go ahead and unlock the wiring connector that runs to the assembly and disconnect the wiring. Repeat the same process on the passengers side. Well now move to inner wheel wells. more
5/4/2012 10:15:58 AM
Trailer Wiring Harness Installation - 2006 Saturn Vue- Video
Today we are going to install part number 118418 from Tow Ready on our 2006 Saturn Vue. The general layout of this wire harness is that the connections are behind the tail lights, route the wires underneath the vehicle, and the wires will be stored outside the vehicle when we are done. To start off, we will take off the tail lights we will lift the hatch to get to those. All right, and here is our connection point right here. So let us pull this latch out and pull it apart. And repeat for the passengers side. All right, next we need to loosen this section of quarter-panel here to give us some room to run our connectors and put our black box for the T-harness hidden back up inside of here. What we are going to do is take out this nut here and this nut here, and that will give us enough wiggle room to pull the panel off just a little bit. more
3/31/2009 9:15:08 AM
Filter Videos
Filter Videos
